table of contentsintroduction 1about this manual 2features of your PowerPlate™ 2warning and tips 3mounting locations 3system planning 4system configur
System 3 - The P850.2 is used in fully active 8-channel mode. Channels 1/2 are high-passed for fronttweeters. Channels 3/4 are bandpassed for front mi
installation1. Disconnect the battery ground cable. Reconnect the ground cable only after the installation is complete and the wiring has been checked
speaker connections for stereo configurations Minimum recommended impedance is 2Ω stereo.Speaker terminals accept up to AWG #12 speaker wire.speaker c
signal sourcesDue to the wide input level adjustment range, all a/d/s/ PowerPlates™ can be driven with either aconventional preamplifier drive signal
Channels 3-8 can be accessed through the din 3-8 connector by using the optional AC202 RCAto DIN adapter for P850.2 only. DIN ch 3-8 connections:pin 1
internal signal routing con’tChannels 5/6 input switch (P650.2 and P850.2) - selects input from three possibilities.When the switch is in the left pos
multi-cross™ crossover configurationxover control 1/2 - The crossover selection switch for channels 1 & 2 has three possibilities:When the switch
multi-cross™ crossover configuration, cont'dxover control 5/6 (P850.2) - The crossover section dedicated forchannels 5 & 6 are activated by d
using the AC502 (optional)The AC502 remote level control, available as an accessory from your a/d/s/ dealer, may be used with yourPowerPlate™ to remo
adjusting input sensitivityThe input sensitivity setting is important to ensure proper performance, low noise levels, and maximumsystem reliability. A
about this manualTo get the most from your a/d/s/ PowerPlate™, we recommend that you have the installation performedby your qualified authorized a/d/s
20a/d/s/ P450.2
21a/d/s/ P650.2
22a/d/s/ P850.2
troubleshootingsymptom possible cause action to takeno output low or no remote turn-on check remote turn-on voltage input output at amplifier and
symptom possible cause action to takedistorted output (cont’d) speakers are blown check system with known working speakers and repair orreplace as nee
specificationsamplifier sectionpower output 4Ω(watts)1 50/channel 150/bridged channel pairpower output 2Ω (watts)2 75/channeldistortion all channels
warranty informationLIMITED TWO YEAR CONSUMER WARRANTYDirected Electronics, Inc. promises to the original purchaser, to replace this product should it
warnings and tipsAlways disconnect the battery ground wire before doing any work on your vehicle. Reconnect the cableonly after the installation is co
system planningProper system planning is the best way to maximize your PowerPlate’s™ performance. By planning yourinstallation carefully you can avoi
P450.2 system diagramsSystem 1 - P450.2 used in 4-channel mode with front and rear full range speakers.System 2 - P450.2 used in 2-channel bridged mod
System 3 - Two P450.2’s, one is used to drive front tweeters and midrange drivers, the second is used in2-channel bridged mode for subwoofers. Subwoof
P650.2 system diagramsSystem 1 - P650.2 used in 6-channel mode. Channels 1/2 are high-passed for front speakers. Channels3/4 are high-passed for rear
System 3 - P650.2 used in 3-channel mode. Channels 1/2 and 3/4 are high-passed and bridged for frontspeakers. Channels 5/6 are low-passed and bridged
P850.2 system diagramsSystem 1 - P850.2 used in 6-channel mode. Channels 1/2 are high-passed for front speakers channels3/4 are high-passed for rear s
Commentaires sur ces manuels